A coordinate is a pair of numbers, but the numbers alone are not the answer; the notation is. Notation states the order (which value leads), the frame (which axes, which origin), and the dialect (degrees or grid meters, letters or signs). The same physical point can be written half a dozen correct ways, and each wrong way fails silently: swapped latitude and longitude still look like coordinates, and they point at a different place on Earth. This guide teaches the grammar system by system, then runs one famous point through all of them. The converter below restyles a pair between the geographic dialects; the rules that follow cover the systems it cannot.
Home / Coordinates and Location Formats
How to Find Coordinate Notation: Reading and Writing Points in Every System

Photo: Jef K / Pexels
Coordinate Converter: One Point, Every Dialect
Enter a decimal pair and read it back in degrees minutes seconds and degrees decimal minutes. Then state the system beside the numbers, the habit this article checklist ends on, before the pair travels anywhere.
From decimal degrees
Your latitude breaks down as 40 degrees, 41 minutes, 21.00 seconds. One degree is 60 minutes, one minute is 60 seconds, so a second of latitude is about 31 meters on the ground.
From degrees minutes seconds
Conversions use the WGS 84 coordinate system, the same one GPS satellites and phone maps use. Plus codes are computed with the open location code algorithm, the same method Google Maps uses.
The Ordered Pair: The Classroom Grammar
In mathematics, a point is written (x, y): round brackets, x first, y second, always in that order. The mnemonic is alphabetical and architectural: x before y, across before up. (3, 4) is the point 3 right and 4 up; (4, 3) is a different point, and no amount of confidence changes that. Three dimensions add z: (x, y, z). A vector wears the same clothes, and angle brackets sometimes distinguish it in print. The notation carries no units and no letters, because the frame is assumed: the origin is (0, 0), the axes are the page's. Everything else in this guide exists because the Earth refuses to be a page.
Latitude and Longitude: The Order Trap and the Three Dialects
Geographic notation breaks the classroom rule, and the break causes real world errors daily. In speech and in most mapping interfaces, the order is latitude first, then longitude: the Statue of Liberty is "40.689167, minus 74.044444," latitude leading. But in data formats built by programmers, GeoJSON and its relatives write longitude first, following the (x, y) habit, because longitude plays the x role on a map. Neither is wrong; each is correct inside its own system, and the notation's job is to tell you which system you are in. Then come the dialects. Decimal degrees: 40.689167, minus 74.044444, signs doing the work of the compass letters. Degrees minutes seconds: 40 degrees 41 minutes 21.00 seconds N, 74 degrees 2 minutes 40.00 seconds W, letters replacing signs, N and E positive, S and W negative. Degrees and decimal minutes: the marine and geocaching dialect, splitting the difference. A complete notation in any dialect must make hemisphere unambiguous: a sign or a letter, never neither, and never both contradicting each other. The full treatment of these formats, with conversion arithmetic, is our latitude and longitude format guide, and the negative number question is answered in can latitude and longitude be negative.

Grid Notation: UTM, MGRS, and Map References
Grid systems replace degrees with meters and their own grammar. UTM notation names the zone first, then easting, then northing: the Eiffel Tower sits in Zone 31U at easting 448,251.80, northing 5,411,932.68. Drop the zone and the numbers are meaningless, because every zone restarts its own meter count; the zone is part of the notation, not a label beside it. MGRS, the military refinement, compresses the same idea into a string of letters and digits whose precision grows with its length: more digits, smaller square. National grid references, like the British two letters plus digits, follow the same rule: letters name the big square, digits refine inside it. Grid notation's shared grammar is read across, then up, eastings before northings, the classroom order restored. The conversions behind these systems are in our latitude and longitude to UTM guide, and the field use of grid references is in army maps and land navigation.
One Point, Every Notation
The Statue of Liberty, written correctly in each system: Ordered pair on a local grid would depend on the grid's origin, which is exactly why local pairs stay local. Decimal degrees: 40.689167, minus 74.044444, latitude first in prose. Degrees minutes seconds: 40 degrees 41 minutes 21.00 seconds N, 74 degrees 2 minutes 40.00 seconds W. GeoJSON order: minus 74.044444, 40.689167, longitude first, in square brackets as an array. UTM: Zone 18T, with easting and northing in meters from that zone's origin. Plus code: a compact string encoding the same patch of ground, the subject of what is a plus code. Six correct answers, one point. The skill is not memorizing them; it is recognizing which grammar a given string is speaking before you trust it, the same skill as reading coordinates on a map or the pairs in latitude and longitude practice.
The Four Notation Traps
The swap. Latitude and longitude reversed. It survives because both numbers often sit in valid ranges; it fails only when a latitude above 90 appears, which is why swaps hide in mid latitudes. Check the frame before the figures. The dropped sign. A longitude written 74.04 with no minus and no W is a point in China instead of New York harbor; hemisphere information is part of the number. The mixed dialect. Degrees for one value, degrees minutes seconds for the other, or a decimal minute read as a second; conversions live in our decimal degrees and degrees minutes seconds guides. The silent default. Software that assumes an order or a datum without saying so; professional habit is to state the system beside any coordinate you publish, which is why every worked example on this site names its frame. And the angles that aim vectors have their own grammar, covered in direction angles of a vector.
Precision Is Part of the Notation Too
A coordinate's decimal places are a claim about accuracy, and the claim should match reality. In decimal degrees, each place after the point divides the resolution by ten: one decimal place locates to about 11 km, two to about 1.1 km, three to about 110 m, four to about 11 m, five to about 1.1 m, and six to about 11 cm. Writing a trailhead as 40.6891672 claims a precision no phone GPS possesses, and truncating a survey point to three decimals throws away accuracy someone measured. The notation habit: carry the places your source earned, no more. Degrees minutes seconds plays the same game in its own units: a second of latitude is about 31 m, so DMS stated to hundredths of a second claims about 31 cm, which is why the Statue of Liberty example in this guide carries two decimals on its seconds. When converting between dialects, convert the precision too; a DMS pair rounded to whole seconds does not become more precise by emerging as six decimal places, it becomes more decorated. The practice sets in latitude and longitude questions and answers drill exactly this judgment.
Notation in the Wild: Addresses, Plus Codes, and Words
Not every location notation is numeric. Street addresses are a notation, a hierarchical one, country, city, street, number, that resolves through a geocoder rather than arithmetic. Plus codes compress coordinates into a short alphanumeric string designed to be spoken and typed, the system explained in what is a plus code, and three word systems divide the planet into named squares for the same reason. These notations trade the coordinate pair's precision and universality for memorability, and they convert back to latitude and longitude when precision matters. The professional lesson across all of them is the one this guide opened with: a location string is only as good as your knowledge of which grammar it speaks. State the system, keep the hemisphere, respect the precision, and the numbers will take you to the right place on Earth, which is the entire job. The photo side of the same discipline, coordinates written invisibly into files, is covered in how to find coordinates from a photo.
A Five Point Notation Checklist for Anything You Publish
Before any coordinate leaves your desk, in a report, a dataset, or a message, run the five checks. System stated: latitude and longitude, UTM with its zone, a named grid, or a local frame, written beside the numbers. Order correct for that system: latitude first in prose, longitude first in GeoJSON, eastings before northings in grids, x before y in pairs. Hemisphere unambiguous: a sign or a letter on each geographic value, agreeing with each other. Precision earned: decimal places matching the source's real accuracy, no decoration added, none thrown away. Datum named where it matters: WGS 84 for GPS sourced points, the local datum where a national grid demands it, because the same numbers on a different datum are a different place by up to hundreds of meters. The checklist is thirty seconds of work, and it prevents the entire taxonomy of errors this guide catalogued: the swap, the dropped sign, the mixed dialect, and the silent default. Professionals are not people who never err; they are people whose errors get caught by the checklist before the coordinates travel.
Related Guides
If this page answered part of the question, these coordinates guides cover the rest of the same ground:
- How to Find the Coordinate System in AutoCAD: Drawing Settings, the CGEOCS Variable, and the Plain AutoCAD Catch: Whether an AutoCAD drawing has a coordinate system at all depends on which AutoCAD you are running.
- How to Find the Coordinate System in Civil 3D: MAPCSASSIGN, the Status Bar, and Drawing Settings: A Civil 3D drawing carries its coordinate system inside the file, and there are four places that will tell you what it is: the MAPCSASSIGN dialog,...
- How to Find Coordinates on Google Maps: Right Click, Long Press, and Reading the Pair: Google Maps hides coordinates in plain sight.
Frequently Asked Questions
What is coordinate notation?
It is the set of rules for writing a point: the order of the values, the brackets or separators, the signs or hemisphere letters, and the system the numbers belong to. (3, 4) in mathematics, 40.689167, minus 74.044444 in geographic prose, and longitude first arrays in GeoJSON are all correct notation inside their own systems.
Why is latitude written before longitude, but GeoJSON uses longitude first?
Prose and mapping tradition lead with latitude. Data formats follow the mathematical (x, y) habit, and longitude plays the x role, so GeoJSON writes longitude first. Both are correct in context; errors happen when a pair written in one grammar is read in the other, which is why the system should always be stated.
How do I write coordinates in degrees, minutes, and seconds?
State degrees, then minutes (60ths of a degree), then seconds (60ths of a minute), with a hemisphere letter: 40 degrees 41 minutes 21.00 seconds N. The letter replaces the sign: N and E are positive, S and W negative. The Statue of Liberty in this dialect is 40 degrees 41 minutes 21.00 seconds N, 74 degrees 2 minutes 40.00 seconds W.
What does the zone mean in UTM coordinates?
UTM divides the Earth into 60 zones, each with its own meter grid and origin. An easting and northing only locate a point inside their zone, so the zone designator, like 31U, is part of the coordinate itself. The same easting and northing in a different zone is a different place entirely.
How can I tell if a coordinate pair is swapped?
Check the frame first: in geographic prose the first number is latitude and cannot exceed 90. If the first value is above 90, the pair is longitude first or wrong. Then sanity check the result against the expected region; a point in the wrong ocean is the swap's signature. When in doubt, convert both orders and see which lands where the source intended.
Photo credits: Jef K (Pexels); Ronaldo Guiraldelli (Pexels). Photos are served from this site; follow the credit to the library page for the original.