Home / Coordinates and Location Formats

How to Find the Coordinate Direction Angles of a Moment: Cross Product First, Then the Angles

Close-up view of a blackboard filled with complex mathematical equations and formulas

Photo: Vitaly Gariev / Pexels

Direction angle problems usually begin with a vector already on the page. A moment problem is ruder: it begins with a force and the position where the force acts, and the vector whose direction angles you need does not exist until you create it. That is the whole structure of this topic, and the reason students lose marks on it in a specific way, by computing beautiful direction angles for the wrong vector, usually for r or for F, which were never asked about. The moment is a vector of its own, M = r x F, perpendicular to both its parents, with its own magnitude and its own direction. Stage one builds it. Stage two, the familiar direction-angle routine from our guide to coordinate direction angles of a vector, describes it. This article does both stages slowly, with every arithmetic step shown, because in a two-stage problem the only real enemy is a silent error in stage one flowing downhill into stage two.

Interactive tool

Moment First, Angles Second: The Checklist

Check off each step as you finish it. Your progress stays on this page.

0 of 7 complete

0% done

What a Moment Is, in One Short Section

A moment is the turning effect of a force about a point. If a force F acts at a point located by the position vector r, measured from the point you are taking moments about, the moment is the cross product M = r x F. Its magnitude is |M| = |r| |F| sin theta, where theta is the angle between r and F when they are placed tail to tail, which is why a force pushing straight through the pivot, theta equal to zero, produces no moment at all. Its direction is given by the right-hand rule: curl the fingers of your right hand from r toward F and your thumb points along M. That direction is not decoration. It is the axis about which the force tries to rotate the body, which is exactly why a problem asks for its coordinate direction angles: the three angles alpha, beta, and gamma that the moment vector makes with the positive x, y, and z axes. Find M first. Then describe M. In that order, always.

Stage One: Build the Moment Vector

With r and F in component form, r = (rx, ry, rz) and F = (Fx, Fy, Fz), the cross product is computed component by component with these three formulas:

  • Mx = ry Fz - rz Fy
  • My = rz Fx - rx Fz
  • Mz = rx Fy - ry Fx

Read the pattern before you use it: each component of M skips its own axis and combines the other two, and the middle component, My, runs in the opposite order from the other two, which is the single most common sign error in this entire topic. Write the formulas down, substitute carefully, and keep every negative sign attached to its number. A force component of -2 is not 2, and a cross product computed with a dropped sign produces a moment pointing somewhere the physics never intended.

Worked Example 1: The Full Problem

A force F = (4, 5, -2) acts at a point located by r = (2, -1, 3) from the origin. Find the coordinate direction angles of the moment about the origin.

Stage one, the cross product, component by component. Mx = ry Fz - rz Fy = (-1)(-2) - (3)(5) = 2 - 15 = -13. My = rz Fx - rx Fz = (3)(4) - (2)(-2) = 12 + 4 = 16. Mz = rx Fy - ry Fx = (2)(5) - (-1)(4) = 10 + 4 = 14. So the moment is M = (-13, 16, 14). Pause and sanity-check the signs before moving on: a negative x component, positive y, positive z. The direction angles must agree with that picture, alpha obtuse because Mx is negative, beta and gamma acute because their components are positive. If stage two ever contradicts the sign picture from stage one, the error is arithmetic, not conceptual.

The magnitude comes next: |M| = sqrt((-13)^2 + 16^2 + 14^2) = sqrt(169 + 256 + 196) = sqrt(621), which is about 24.92. Stage two is now three divisions and three inverse cosines. cos alpha = Mx / |M| = -13 / 24.92 = -0.5217, so alpha = 121.44 degrees. cos beta = 16 / 24.92 = 0.6421, so beta = 50.05 degrees. cos gamma = 14 / 24.92 = 0.5618, so gamma = 55.82 degrees. The answers behave exactly as the sign picture predicted: one obtuse angle for the negative component, two acute angles for the positive ones.

The Check That Catches Everything

Direction angles are not three independent facts; they are bound by an identity. For any vector, cos^2 alpha + cos^2 beta + cos^2 gamma = 1, exactly. Run it on the example: (-0.5217)^2 + (0.6421)^2 + (0.5618)^2 = 0.2722 + 0.4123 + 0.3156, which sums to 1.0000 up to rounding. This check costs twenty seconds and it is merciless: a wrong magnitude, a dropped sign, a component copied from r instead of M, all of them break the identity loudly. Make it a reflex. In a two-stage problem your stage one has three separate chances to go wrong, and this identity audits the combined result of both stages at once. Our companion guide to coordinate direction angles treats the identity and the geometry behind it in more depth.

Close-up of mechanics hands repairing engine, showcasing teamwork and skill
Close-up of mechanics hands repairing engine, showcasing teamwork and skill

Worked Example 2: A Smaller Moment

A force F = (0, 3, 4) acts at r = (1, 2, 0). Stage one: Mx = ry Fz - rz Fy = (2)(4) - (0)(3) = 8 - 0 = 8. My = rz Fx - rx Fz = (0)(0) - (1)(4) = 0 - 4 = -4. Mz = rx Fy - ry Fx = (1)(3) - (2)(0) = 3 - 0 = 3. So M = (8, -4, 3), with magnitude |M| = sqrt(64 + 16 + 9) = sqrt(89), about 9.43. Stage two: cos alpha = 8 / 9.43 = 0.8480, so alpha = 32.01 degrees. cos beta = -4 / 9.43 = -0.4240, so beta = 115.09 degrees, obtuse as the negative My demands. cos gamma = 3 / 9.43 = 0.3180, so gamma = 71.46 degrees. Check: 0.8480^2 + 0.4240^2 + 0.3180^2 = 0.7191 + 0.1798 + 0.1011 = 1.0000. Notice how much of this example was zeros: a zero component in r or F does not make a zero moment component, it just simplifies one term of each formula, and the My sign flip still applies even when its first term vanishes.

The Extension: Moment About a Specified Axis

Some problems ask a harder question: not the direction of the whole moment, but the size of the moment about one chosen axis, a hinge line, a shaft, a door's edge. That quantity is a scalar, found with the scalar triple product: project the moment onto the axis. If u is the unit vector along the axis, the moment about the axis is u . (r x F), the dot product of the axis direction with the full moment vector. The direction-angle skill in this article is what lets you build u from a described axis and interpret the result: a positive value means the moment acts in the u direction by the right-hand rule, negative means opposite. Master the two-stage problem here and the axis version is one dot product standing on top of it.

Units, Scaling, and What the Angles Ignore

A closing reassurance about the answers themselves. Direction angles are pure direction: they carry no units, and they do not change if the problem is rescaled. Measure r in meters and F in newtons and the moment comes out in newton-meters; measure r in feet and the same physical setup gives a moment in pound-feet with a different magnitude, but the moment vector points along the same axis, so alpha, beta, and gamma come out identical. Doubling the force doubles |M| and leaves every direction cosine untouched, because each cosine divides a component by the magnitude and the doubling cancels. This is worth knowing in an exam for a practical reason: if your three angles look wildly different from a classmate's while your moment components are simple multiples of theirs, one of you has an arithmetic slip in a component, not a conceptual disagreement, and the squared-cosines check plus the sign picture will find it in under a minute.

The Three Errors That Cost the Marks

First, taking the direction angles of the wrong vector. The problem asks about M; students under time pressure describe r, because r is the vector they were handed first. Circle what the question asks before computing anything. Second, the My sign. The middle component of a cross product is rz Fx - rx Fz, the reverse order of its siblings; computing it as rx Fz - rz Fx flips the sign of My, which flips beta from acute to obtuse or back, and the squared-cosines check will not catch it, because a sign flip leaves squares unchanged. The sign picture will catch it: compare each component's sign against its angle's size, every time. Third, using the magnitude of r or of F in stage two's divisions. The only magnitude that belongs under M's components is |M|. Label every number with the vector it belongs to and these three errors mostly design themselves out of your work.

Related Guides

The closest companions to this guide are the coordinates guides below. Each one picks up a thread this page starts:

Frequently Asked Questions

Why do I have to compute the cross product before finding direction angles?

Because the direction angles belong to the moment vector, and the moment vector does not exist until you build it as M = r x F. The problem gives you a force and a position, not a moment. Taking direction angles of r or F answers a question nobody asked. Stage one creates the vector; stage two describes it.

What are the component formulas for the moment?

For r = (rx, ry, rz) and F = (Fx, Fy, Fz): Mx = ry Fz - rz Fy, My = rz Fx - rx Fz, and Mz = rx Fy - ry Fx. Each component combines the two axes it does not name, and the middle component runs in reverse order, which is the classic sign trap in this calculation.

How do I check my three direction angles?

Two checks, both cheap. The identity: cos^2 alpha + cos^2 beta + cos^2 gamma must equal 1. And the sign picture: a negative component must produce an obtuse angle, a positive component an acute one, a zero component exactly 90 degrees. The identity catches magnitude and arithmetic errors; the sign picture catches the flipped My that the identity cannot see.

Can a direction angle of a moment be more than 90 degrees?

Yes. Direction angles run from 0 to 180 degrees, and any negative component makes its angle obtuse. In worked example 1 above, Mx is negative and alpha is 121.44 degrees. An answer set with all three angles acute is possible only when all three components are positive, so an all-acute answer for a mixed-sign moment is a red flag.

How is the moment about an axis different from the moment about a point?

The moment about a point is the full vector M = r x F, with a magnitude and direction angles. The moment about an axis is one scalar: the component of that vector along the axis, computed as the scalar triple product u . (r x F), where u is the unit vector along the axis. The vector comes first in both cases; the axis version then projects it.

Photo credits: Vitaly Gariev (Pexels); Sergei Starostin (Pexels). Photos are served from this site; follow the credit to the library page for the original.