A grid reference is a superb local address and a useless global one. Inside Britain, "TL 449 594" finds a 100 meter square near Cambridge with total reliability; paste it into a tool expecting latitude and longitude and you get nothing. Converting between the two is a small chain of well defined steps, and one of them, the datum shift, is the step everyone skips and the only one that can put you in the wrong field. Our guide to grid references covers reading them off the map; this article owns converting them out, into decimal degrees the rest of the world understands.
Home / Coordinates and Location Formats
Grid Reference to Decimal Degrees: From an OS Grid Reference to Latitude and Longitude

Photo: Maik Poblocki / Pexels
Coordinate Converter: Check Your Grid Conversion
Convert the decimal result of your grid reference here and compare. The point should land inside the original square, and converting back should return the same reference at its own precision.
From decimal degrees
Your latitude breaks down as 40 degrees, 41 minutes, 21.00 seconds. One degree is 60 minutes, one minute is 60 seconds, so a second of latitude is about 31 meters on the ground.
From degrees minutes seconds
Conversions use the WGS 84 coordinate system, the same one GPS satellites and phone maps use. Plus codes are computed with the open location code algorithm, the same method Google Maps uses.
Step One: The Letters Name a 100 Kilometer Square
The National Grid tiles Britain with squares of 100 km, each identified by two letters. The first letter names a 500 km block, the second a 100 km square within it. TL, for example, is the square whose southwest corner sits 400 km east and 200 km north of the grid's origin, which lies off the Isles of Scilly. The letters skip I to avoid confusion with the number 1, a small mercy that matters when references are read over radios in rain. To convert, you first translate the letter pair into the easting and northing of that square's southwest corner, using the published grid diagram or a lookup table; every converter and the Ordnance Survey's own guide carries the same table, because the letters are pure bookkeeping.
Step Two: The Digits Locate You Inside the Square
The numbers after the letters split in half: the first half is the easting offset within the square, the second half the northing. A six figure reference like 449 594 carries three digits per half, each digit a step of 100 meters: easting 449 means 44.9 km east of the square's southwest corner, northing 594 means 59.4 km north of it. Add the offsets to the square's corner values and you hold the full National Grid coordinate: for TL 449 594, an easting of 444,900 meters and a northing of 259,400 meters. Longer references simply refine the same point: eight figures resolve to 10 meters, ten figures to 1 meter. Nothing about this step is approximate; the grid is a clean Cartesian system, and the arithmetic is exact.

Step Three: Easting and Northing to Latitude and Longitude (in OSGB36)
Now the geometry. The National Grid is a transverse Mercator projection of the Earth, with a true origin at 49 degrees north, 2 degrees west, a scale factor of 0.9996012717 on the central meridian, and a false origin that keeps all British coordinates positive: eastings count from a point 400 km west of the true origin's meridian, northings from 100 km south of the true origin's latitude. Converting easting and northing back to latitude and longitude means inverting that projection, a job for the formulae Ordnance Survey publishes in its guide to coordinate systems, involving a series expansion around the meridian. Nobody sane does this by hand twice; you use the published formulae in a spreadsheet or script, or a converter that implements them. The result at this stage is a latitude and longitude in the OSGB36 datum, and the italic warning matters more than the numbers.
The Datum Shift: OSGB36 Is Not WGS 84
Here is the hundred meter trap. OSGB36 is a local datum, fitted to Britain using the Airy 1830 ellipsoid, surveyed in the age of theodolites. WGS 84 is the global datum GPS uses. The same physical point has different latitude and longitude in the two systems, and across Britain the difference runs to roughly 100 meters, varying by place. Convert a grid reference with the projection math and plot the OSGB36 result directly in a GPS tool, and your point sits a field or a street away from the truth, close enough to look right and wrong enough to matter.
The correct finish is a datum transformation, and for Britain the proper one is OSTN15, the Ordnance Survey's official transformation, which models the local distortions of the old triangulation network rather than applying one smooth shift. Quality converters and the OS's own tools apply OSTN15 silently; cheap ones apply a rough seven parameter shift or none at all. When accuracy matters, verify which transformation your tool used. When it does not matter, when you need a town level answer rather than a gate level one, even the rough shift beats forgetting the datum exists.
The Worked Example, End to End
Take TL 449 594. Letters: the TL square's southwest corner is at easting 400,000, northing 200,000. Digits: add 44,900 east and 59,400 north, giving easting 444,900, northing 259,400. Projection inversion gives a latitude and longitude near 52.2 degrees north, 0.12 degrees east in OSGB36, and the OSTN15 transformation nudges that point by on the order of a hundred meters into its WGS 84 position, in the countryside just east of Cambridge. Every grid reference in Britain converts by this same chain, and the chain has exactly three places to go wrong: misreading the letter square, splitting the digits unevenly (a five figure reference is a misprint, not a format), and skipping the datum. Check those three and the conversion is trustworthy to the resolution of the reference itself: a six figure reference names a 100 meter square, so its decimal degree answer honestly carries about four decimal places of meaning, no matter how many digits the converter displays.
Where Conversions Go Wrong Before the Math Starts
Most failed conversions are reading failures, not calculation failures, and they cluster in three places. Uneven digit splits. A reference's numbers always split into two equal halves. An odd count of digits means a transcription error somewhere upstream, a dropped zero being the classic, and converting it anyway manufactures a confidently wrong point. The missing letter pair. Digits alone locate nothing; 449 594 exists in every 100 km square in Britain, which is to say in over a hundred places at once. References quoted without letters, common in local documents that assume local knowledge, are incomplete data and must be completed from context before conversion, not after. Confusing the systems. Britain's National Grid is not the military grid (MGRS) and not the Irish or Channel Island grids, each of which has its own letters, datum, and conversion path. A reference that will not parse is often a perfectly good reference in a neighboring system, and the fix is recognizing which country and which grid you are holding before reaching for the formulae.
Why the Grid Refuses to Die
It is fair to ask why anyone converts from grid references at all, in a world that runs on latitude and longitude. Because inside Britain the grid is genuinely better for its home jobs. It is metric and square: distances and areas read straight off it with school arithmetic, which is why planning, land management, utilities, and the emergency services work in it daily, and why mountain rescue in Britain still takes grid references over the phone, six figures being short, unambiguous, and tied to the paper maps both ends may be holding. Decimal degrees win globally because they are global. The grid wins locally because it was designed for one island's work in meters. Conversion is the customs post between two legitimate systems, and like a customs post it rewards travelers who arrive with their documents in order: letters, even digits, and the datum step respected.
Verify by Converting Back
Every conversion in this article deserves the ten second audit that catches nearly all of its errors: convert the result back. Take your decimal degrees, run them through the reverse path (the same OS tool converts in both directions; any converter worth using offers the return trip), and compare the grid reference you get with the one you started from. Agreement at the level of the original reference, the same square at six figures, the same ten meter cell at eight, means the forward conversion is sound. The expected mismatch is zero at the reference's own precision: your decimal point sits somewhere inside the original square, conventionally its southwest corner or its center depending on the tool's habit, so a back conversion may return the square shifted by half a cell if the two tools made different centering choices. That half cell wobble is convention, not error. A back conversion that lands in a different square entirely is an error, and its size tells you the diagnosis: one square off is a rounding or centering slip, a hundred kilometers off is a letter or datum problem, and a point in the sea off Cornwall is the missing OSGB36 step announcing itself.
Keep the Pair Together
One final discipline: a converted coordinate should never travel alone. Record the decimal degrees and the original grid reference, with the datum step noted, in the same document, spreadsheet, or database row. The pair is self auditing, anyone can re-derive either from the other and check your work, and when (not if) a question arises years later about which square a point came from, the original reference answers it in the system's own language, at its original precision, with nothing lost to rounding. Conversions are cheap and references are forever; the professionals keep both, and so should you.
Related Guides
If this page answered part of the question, these coordinates guides cover the rest of the same ground:
- Latitude and Longitude to MGRS: How the Military Grid Reference System Works: MGRS turns a latitude and longitude into a compact grid reference like 18S UJ 23478 06483: a grid zone designator, a 100 kilometer square, and...
- How to Find Coordinates Rotated 90 Degrees: The Rules for Clockwise, Counterclockwise, and Any Center: Rotating a point 90 degrees is a swap and a sign change: counterclockwise about the origin, (x, y) becomes (-y, x); clockwise, it becomes (y, -x).
- How to Find a Coordinate Point in AutoCAD: ID, Status Bar, LIST, and Bulk Export: AutoCAD knows the coordinates of every point in a drawing, and offers five ways to read them, from the one click ID command to a full...
Frequently Asked Questions
How do I convert a grid reference to latitude and longitude?
In three steps: translate the two letters into the southwest corner of their 100 km square, add the digit halves as easting and northing offsets within the square, then invert the National Grid projection using the Ordnance Survey formulae and apply the OSTN15 datum transformation to reach WGS 84 latitude and longitude. In practice, use a converter that implements the OS formulae and OSTN15, and verify it does both.
Why is my converted point about 100 meters off?
You are looking at the datum difference. Grid references live in OSGB36; GPS tools live in WGS 84; the same point has coordinates roughly 100 meters apart between the two systems in Britain. A converter that skips the datum transformation, or uses a rough shift, leaves most of that error in your result. Use one that applies OSTN15, the official transformation.
What do the letters in a grid reference mean?
They identify a 100 km square of the National Grid. The first letter selects a 500 km block, the second a 100 km square inside it, and together they give the easting and northing of the square's southwest corner, to which the numeric halves of the reference are added. The letter I is skipped to avoid confusion with the number 1.
How accurate is a six figure grid reference after conversion?
A six figure reference identifies a 100 meter square, so the converted latitude and longitude carry about four decimal places of real meaning. Ten figure references resolve to 1 meter and justify about five places. Extra digits printed by a converter beyond the reference's own resolution are arithmetic, not accuracy.
Can I convert grid references in bulk?
Yes. The chain is pure arithmetic plus the OSTN15 shift, and it scripts well: parse the letters through the square table, split the digits, apply the OS projection formulae, then the transformation. The Ordnance Survey publishes both the formulae and the transformation data for exactly this purpose, and GIS software such as QGIS performs the whole conversion by reprojecting from EPSG:27700 (the National Grid) to EPSG:4326 (WGS 84).
Photo credits: Maik Poblocki (Pexels); Gundula Vogel (Pexels). Photos are served from this site; follow the credit to the library page for the original.